2 курс Презентация к уроку английского языка по теме "Fasteners" (Крепёж) в профессиональном учебном заведении
презентация к уроку

Слайд 1

Fasteners Презентация урока по теме «Крепёж» Преподаватель англ.языка СПб ГБПОУ «Автодорожный колледж» Лебедева Е.Н.

Слайд 2

Презентация к уроку по теме « Fasteners » 2 курс, специальность «Автомеханик» Преподаватель английского языка СПб ГБОУ «Автодорожный колледж» Лебедева Е.Н.

Слайд 3

FASTENERS КРЕПЁЖ

Слайд 4

ANCHOR Анкер

Слайд 5

CLAMP Тиски, фиксаторзажим

Слайд 6

washer шайба

Слайд 7

nut гайка

Слайд 8

screw винт

Слайд 9

nail гвоздь

Слайд 10

Метрическая резьба Metric thread

Слайд 11

UTS Thread резьба

Слайд 12

Reading: Which fastener is right for your job? If you need a temporary fastener, go with a pin or clamp . Nails are a quick and long-lasting fastener. They are idealfor walls and wood surfaces. Screws are a more secure fastener. Wood screws are best for solid wood surfaces. But sheet metal screws work on wood as well as other surfaces.

Слайд 13

Remember to check the correct thread for your project. This store carries both UTS thread and metric thread measurements. Use an anchor for situations requiring extra support.

Слайд 14

Use bolts when pressing pieces together from both sides. Select a bolt with the appropriate grade . Otherwise, the bolt may break. Get the right washers and nuts to add strength and prevent damage to surfaces.

Слайд 15

Read the poster. Then, mark the following statements as true (T) or false (F) 1 – Clamps are long-lasting fasteners. 2 – Sheet metal screws will damage wood surfaces. 3 – Washers protect surfaces from damage.

Слайд 16

Vocabulary: match the words (1-7) with the definitins (A-G)

Слайд 17

A – a piece of metal with a hole tn the middle B – a long, narrow fastener with a smooth rod C – a device that tightly presses things together D – a thread measured in millimetres E – the measurement of bolt’s strength F – a device that adds support to a screw G – a fastener with threads along the entire rod

Слайд 18

Read the sentences pair. Choose where the words best fit the blanks. 1) screw/washer A – Place a _______ between the nut and surfaces. B – The hook is attached to the wall with a ______ . 2) bolt / thread A – Jules attached the table leg with a _______. B – I don’t know the best _____ size for the screws.

Слайд 19

3) fastener / UTS thread A – The mechanic was only familiar with _____ sizes, not metric . B – The hardware store was known for having a ______ for every project. 4) pin / wood screw A – A ______ is not effective on metal. B – Albert used a ______ to hold the board together temporarily.

Слайд 20

Listening: Listen to a conversation between a mechanic and a customer. Choose the correct answers. What is the conversation mainly about? A – an explanation of a repair B – an estimate of repair costs C – a set of maintenance instructions D – a descriptio of a broken appliance

Слайд 21

2) What can you infer about the new bolts? A They do not require washers. B They cost less than the old bolts. C They are a higher grade than the old bolts. D They are specially made for air conditioners.

Слайд 22

Speaking: With a partner, act out the roles using language such as: I repaired ....... How did ...... You needed ...... Student A: You are a mechanic. Talk to Student B about: an air conditioner loose fasteners your repairs Student B: You are a customer. Talk to Student A about an air conditioners.

Слайд 23

Writing: Use the conversation from your speaking to fill out the mechanic’s invoice. Summary of Services Item repaired: ______________________ Problem with item: ___________________ Description of repaires: _________________

Слайд 24

Литература: Учебник Jim D.Dearholt Mechanics Published by Express Publishing 2012